該產品以丙烯酸樹脂為基料，以P-N膨脹阻燃體系為主料采用美國技術、全封閉自動化生產，具有優異的耐候性、耐水性、耐酸堿性和耐曝熱性等性能；同時具有粘接強度高、耐火極限長、裝飾效果好等特殊性能；由國家公安部消防產品合格評定中心抽樣，由國家固定滅火系統和耐火構件質量監督檢驗中心型式認可檢驗，產品各項理化性能指標和防火性能指標完全達到或超過GB14907-2002鋼結構防火涂料標準要求。
一、產品簡介
該產品以丙烯酸樹脂為基料，以P-N膨脹阻燃體系為主料采用美國技術、全封閉自動化生產，具有優異的耐候性、耐水性、耐酸堿性和耐曝熱性等性能；同時具有粘接強度高、耐火極限長、裝飾效果好等特殊性能；由國家公安部消防產品合格評定中心抽樣，由國家固定滅火系統和耐火構件質量監督檢驗中心型式認可檢驗，產品各項理化性能指標和防火性能指標完全達到或超過GB14907-2002鋼結構防火涂料標準要求。
This product is used Acrylic acid Polymers as base material, and P-N intumescent flame retardant as main material. It is produced in Full closed automation by America Technology. With excellent weather resistance, water resistance, acid resistance, alkali resistance and insolation resistance. It is also with high bond strength, long fire endurance, good decoration. It has been sampled by China Certification Center For Fire Products Ministry of Public Security, and taken the Type Approval Survey by CNCF(China National Center for Quality Supervision and Test of Fixed-fighting Systems and Fire-resisting Building Components). All the performance indicators reache or exceed the GB14907-2002.
二、產品特性
2、PRODUCT FEATURES
優異的耐候性、耐水性、耐酸堿性耐曝熱性能優異粘接強度高、耐火極限長裝飾效果好
Excellent weather resistance, water resistance, acid resistance, alkali resistance and insolation resistance. High bond strength, long fire endurance and good decoration.
三、應用領域
3、APPLICATION FIELDS
廣泛適用于油田鉆井平臺井架、石油化工鋼構設施、發電廠、核電站等大型室外剛結構防火保護工程中。
It is widely used in the fire protection of large outdoor steel structureto just like oil rig derric, Petrochemical steel facilities, power station, nuclear power station,and so on.
四、產品說明
4、 CONSTRUCTION TECHNOLOGY
1. 涂刷前鋼結構表面應做防銹處理，表面清潔無油污、灰塵，涂刷防銹漆兩遍；
1）The surface of steel structure should be rust-proof before coating. Make sure the surface is clean, and coating anticorrosive paint twice.
2、施工前應先攪拌均勻，如粘度大可加2-5％稀釋劑稀釋后施工；
2)Stir well before used. When the viscosity is high, could dilute it with 2-5% dilution.
3、每遍間隔不少于24小時，刷(輥)涂2-10遍，厚度達到要求為止，第一遍厚度不要超過200μm，以后每遍厚度不超過300μm；
3) Brush coating 2-10 times until the thickness is enough. Never less than 24h between each coating. The thickness shouldn’t be over 200μm for the first coating, and not over 300μm each time later.
4、可根據顏色要求涂刷面漆一至二道；
4) Coat the finish coats 1-2 times if there is color needs.
5、施工操作應在室內避雨棚進行，施工環境0-38℃；
5) The coating should be going on indoor where the temperature is 0-38℃.
6、漆膜未實干前嚴防雨淋。
6) Prevent the rain until the film is dry enough.
7、涂裝用量（理論用量）
7) DOSAGE
| 耐火極限要求 | 2h | 1.5h | 1h |
涂層厚度 | 2.1mm | 1.6mm | 1.1mm |
涂刷遍數 | ＞7-8道 | ＞5-6道 | ＞3-4道 |
用量（kg/m2） | 約3.1-3.3 | 約2.3-2.5 | 約1.5-1.7 |
Fire endurance | 2h | 1.5h | 1h |
Coating thickness | 2.1mm | 1.6mm | 1.1mm |
Coat times | ≥7-8times | ≥5-6times | ≥3-4times |
dosage（kg/m2） | 3.1-3.3 | 2.3-2.5 | 1.5-1.7 |
五、注意事項
5、ANNOUNCEMENTS
1、應隔絕火種、遠離熱源；
1）Isolate fire, away from the heat.
2、貯存于0一38℃的環境中，防止曝曬；
2) Store in 0-38℃, keep away from sun and heat.
3、貯存期為12個月。
3) Storge life: 12 months.
