該產品采用水性彈性樹脂作為基料的水性鋼結構防火涂料，適用于室內鋼結構表面的防火保護，產品具有環保、耐火極限長、粘接強度高、施工方便等特點。由國家公安部消防產品合格評定中心抽樣，由國家固定滅火系統和耐火構件質量監督檢驗中心型式認可檢驗，產品格項性能指標完全達到或超過GB 14907－2002鋼結構防火涂料標準要求。
一、產品簡介
1、PROSPECTUS
該產品采用水性彈性樹脂作為基料的水性鋼結構防火涂料，適用于室內鋼結構表面的防火保護，產品具有環保、耐火極限長、粘接強度高、施工方便等特點。由國家公安部消防產品合格評定中心抽樣，由國家固定滅火系統和耐火構件質量監督檢驗中心型式認可檢驗，產品格項性能指標完全達到或超過GB 14907－2002鋼結構防火涂料標準要求。
The product is a kind of fire retardant coating for steel structure, that is based on water-borne resin emulsion. It is used in flameproof protection of the surface of the indoor steel structure. It has the special properties like environmental, long fire resistance, high bonding strength and easy to construct. It has been sampled by China Certification Center For Fire Products Ministry of Public Security, and taken the Type Approval Survey by CNCF(China National Center for Quality Supervision and Test of Fixed-fighting Systems and Fire-resisting Building Components). All the performance indicators reache or exceed the GB14907-2002.
二、產品特性
2、PRODUCT FEATURES
粘接強度高、耐火極限長、裝飾效果好、綠色環保無污染、施工方便。
1）High bonding strength; 2）Long fire resistance; 3）Good decorative effect; 4） environmental; 5）Easy to construct.
三、應用領域
3、APPLICATION FIELDS
廣泛應用于建筑物及構筑物室內鋼結構、建筑網架的防火保護。也可以用于石油、化工、治金、電力、煤碳等工、礦、廠房鋼結構的防火保護。
It is widely applicable to the fire protection for buildings or other structures, the indoor bearing steelwork of the large steelwork workshorp and the steel grid structure. It also can be used for the steel-structure building of petroleum industry, chemical industry, metallurgical industry, electric utility and Coal industry.
四、施工工藝
4、CONSTRUCTION TECHNOLOGY
1、鋼結構底材要做除污、防銹處理，一般至少涂刷兩道優質防銹底漆。
1） Clean the dust and the attachments on the surface of steel structure clearly. Must derust the parts which get rusty. Anticorrosive paint twice.
2、待底漆干透，清除防銹漆表面塵土、污物后方可涂刷NB-1室內薄型鋼結構防火涂料。
2） The NB-1 could be used when the anticorrosive paint is dry enough, and there is no dust on the surface.
3、NB-1室內薄型鋼結構防火涂料一般采用刷涂、輥涂或噴涂工藝進行施工。涂料在使用前，須充分攪拌均勻。
3） Fully stir well before used. The coating method like Spraying, roller coating, brush could be used.
4、為保證附著力，施工時第一遍涂層厚度須≤0.3mm，待前遍涂層干透后再涂下一道，以后每遍涂層厚度≤0.5mm，直至總厚度達到設計要求。
4） The thickness of the coating should control in 0.3mm in the first time construct to ensure the intercoat adhesion. Then to the next coating ,each thickness should control in 0.4mm, until the total thickness is up to the standard.
5、該產品為水性涂料，施工溫度10℃以上為宜，濕度不大于85%，遇有雨、雪、霧、大風天氣或鋼材表面有結露時，不宜施工。
5） The temperature when the construction is going on should be above 10℃, for this product is water-borne, and the humidity should be lower than 85%. It couldn’t going on when there’s raining, snowing, misting, winding or dewing on the surface.
6、未用完的涂料應密封保存，已備再用。
6） The rest of the coating should be sealed so that next time still be useful.
五、涂裝用量（理論值）：
DOSAGE
耐火極限 | 3h | 2.5h | 2h | 1.5h | 1.0h |
涂層厚度 | 4.5mm | 3.7mm | 3.0mm | 2.3mm | 1.6mm |
理論用量 | 5.8kg | 4.8kg | 3.9kg | 2.95kg | 1.95kg |
Fire endurance | 3h | 2.5h | 2h | 1.5h |
Coating thickness | 4.5mm | 3.7mm | 3.0mm | 2.2mm |
Dosage（kg/m2 | 5.8kg | 4.8kg | 3.9kg | 1.95kg |
六、注意事項
6、ANNOUNCEMENTS
1、施工要嚴格控制產品用量，確保涂層厚度滿足要求；
2、本產品為一般性危險品運輸；
3、貯存于0~38℃的環境中，隔絕火種，遠離熱源，防止曝曬；
3） Store in 0-38℃, keep away from sun and heat.
4、貯存期為12個月。
4） Storge life:12months.
